transistor

/tran zis"teuhr/, n.

1. Electronics. a semiconductor device that amplifies, oscillates, or switches the flow of current between two terminals by varying the current or voltage between one of the terminals and a third: although much smaller in size than a vacuum tube, it performs similar functions without requiring current to heat a cathode.

2. Informal. a transistorized radio.

adj.

3. Informal. transistorized: a transistor radio.

[1945-50; TRANS(FER) + (RES)ISTOR]

* * *

Solid-state semiconductor device for amplifying, controlling, and generating electrical signals.

Invented at Bell Labs (1947) by John Bardeen, Walter H. Brattain, and William B. Shockley, it displaced the vacuum tube in many applications. Transistors consist of layers of different semiconductors produced by addition of impurities (such as arsenic or boron) to silicon. These impurities affect the way electric current moves through the silicon. Transistors were pivotal in the advancement of electronics because of their small size, low power requirements, low heat generation, modest cost, reliability, and speed of operation. Single transistors were superseded in the 1960s and '70s by integrated circuits; present-day computer chips contain millions of transistors. Today transistors perform many different functions in nearly every type of electronic equipment.

* * *

▪ electronics

Introduction

       semiconductor device for amplifying, controlling, and generating electrical signals. Transistors are the active components of integrated circuits (integrated circuit), or “microchips,” which often contain millions of these minuscule devices etched into their shiny surfaces. Deeply embedded in almost everything electronic, transistors have become the nerve cells of the Information Age.

 There are typically three electrical leads in a transistor, called the emitter, the collector, and the base—or, in modern switching applications, the source, the drain, and the gate (see figure—>). An electrical signal applied to the base (or gate) influences the semiconductor material's ability to conduct electrical current, which flows between the emitter (or source) and collector (or drain) in most applications. A voltage source such as a battery drives the current, while the rate of current flow through the transistor at any given moment is governed by an input signal at the gate—much as a faucet valve is used to regulate the flow of water through a garden hose.

      The first commercial applications for transistors were for hearing aids and “pocket” radios (radio) during the 1950s. With their small size and low power consumption, transistors were desirable substitutes for the vacuum tubes (electron tube) (known as “valves” in Great Britain) then used to amplify weak electrical signals and produce audible sounds. Transistors also began to replace vacuum tubes in the oscillator circuits used to generate radio signals, especially after specialized structures were developed to handle the higher frequencies and power levels involved. Low-frequency, high-power applications, such as power-supply inverters that convert alternating current (AC) into direct current (DC), have also been transistorized. Some power transistors can now handle currents of hundreds of amperes at electric potentials over a thousand volts.

      By far the most common application of transistors today is for computer memory chips—including solid-state multimedia storage devices for electronic games, cameras, and MP3 players—and microprocessors (microprocessor), where millions of components are embedded in a single integrated circuit. Here the voltage applied to the gate electrode, generally a few volts or less, determines whether current can flow from the transistor's source to its drain. In this case the transistor operates as a switch: if a current flows, the circuit involved is on, and if not, it is off. These two distinct states, the only possibilities in such a circuit, correspond respectively to the binary 1s and 0s employed in digital computers. Similar applications of transistors occur in the complex switching circuits used throughout modern telecommunications systems. The potential switching speeds of these transistors now exceed a gigahertz, or more than a billion on-and-off cycles per second.

Development of transistors

      The transistor was invented in 1947–48 by three American physicists, John Bardeen (Bardeen, John), Walter H. Brattain (Brattain, Walter H.), and William B. Shockley (Shockley, William B.), at the American Telephone and Telegraph Company's Bell Laboratories. The transistor proved to be a viable alternative to the electron tube and, by the late 1950s, supplanted the latter in many applications. Its small size, low heat generation, high reliability, and low power consumption made possible a breakthrough in the miniaturization of complex circuitry. During the 1960s and '70s, transistors were incorporated into integrated circuits, in which a multitude of components (e.g., diodes, resistors, and capacitors) are formed on a single “chip” of semiconductor material.

Motivation and early radar research

      Electron tubes are bulky and fragile, and they consume large amounts of power to heat their cathode filaments and generate streams of electrons; also, they often burn out after several thousand hours of operation. Electromechanical switches, or relays, are slow and can become stuck in the on or off position. For applications requiring thousands of tubes or switches, such as the nationwide telephone systems developing around the world in the 1940s and the first electronic digital computers, this meant constant vigilance was needed to minimize the inevitable breakdowns.

      An alternative was found in semiconductors, materials such as silicon or germanium whose electrical conductivity lies midway between that of insulators such as glass and conductors such as aluminum. The conductive properties of semiconductors can be controlled by “doping” them with select impurities, and a few visionaries had seen the potential of such devices for telecommunications and computers. However, it was military funding for radar development in the 1940s that opened the door to their realization. The “superheterodyne” electronic circuits used to detect radar waves required a diode rectifier—a device that allows current to flow in just one direction—that could operate successfully at ultrahigh frequencies over one gigahertz. Electron tubes just did not suffice, and solid-state diodes based on existing copper-oxide semiconductors were also much too slow for this purpose.

      Crystal rectifiers based on silicon and germanium came to the rescue. In these devices a tungsten wire was jabbed into the surface of the semiconductor material, which was doped with tiny amounts of impurities, such as boron or phosphorus. The impurity atoms assumed positions in the material's crystal lattice, displacing silicon (or germanium) atoms and thereby generating tiny populations of charge carriers (such as electrons (electron)) capable of conducting usable electrical current. Depending on the nature of the charge carriers and the applied voltage, a current could flow from the wire into the surface or vice-versa, but not in both directions. Thus, these devices served as the much-needed rectifiers operating at the gigahertz frequencies required for detecting rebounding microwave radiation in military radar systems. By the end of World War II, millions of crystal rectifiers were being produced annually by such American manufacturers as Sylvania and Western Electric (Western Electric Company Inc.).

Innovation at Bell Labs

      Executives at Bell Labs had recognized that semiconductors might lead to solid-state alternatives to the electron-tube amplifiers and electromechanical switches employed throughout the nationwide Bell telephone system. In 1936 the new director of research at Bell Labs, Mervin Kelly, began recruiting solid-state physicists. Among his first recruits was William B. Shockley (Shockley, William B.), who proposed a few amplifier designs based on copper-oxide semiconductor materials then used to make diodes. With the help of Walter H. Brattain (Brattain, Walter H.), an experimental physicist already working at Bell Labs, he even tried to fabricate a prototype device in 1939, but it failed completely. Semiconductor theory could not yet explain exactly what was happening to electrons inside these devices, especially at the interface between copper and its oxide. Compounding the difficulty of any theoretical understanding was the problem of controlling the exact composition of these early semiconductor materials, which were binary combinations of different chemical elements (such as copper and oxygen).

      With the close of World War II, Kelly reorganized Bell Labs and created a new solid-state research group headed by Shockley. The postwar search for a solid-state amplifier began in April 1945 with Shockley's suggestion that silicon and germanium semiconductors could be used to make a field-effect amplifier (see integrated circuit: Field-effect transistors (integrated circuit)). He reasoned that an electric field from a third electrode could increase the conductivity of a sliver of semiconductor material just beneath it and thereby allow usable current to flow through the sliver. But attempts to fabricate such a device by Brattain and others in Shockley's group again failed. The following March, John Bardeen (Bardeen, John), a theoretical physicist whom Shockley had hired for his group, offered a possible explanation. Perhaps electrons drawn to the semiconductor surface by the electric field were blocking the penetration of this field into the bulk material, thereby preventing it from influencing the conductivity.

      Bardeen's conjecture spurred a basic research program at Bell Labs into the behaviour of these “surface-state” electrons. While studying this phenomenon in November 1947, Brattain stumbled upon a way to neutralize their blocking effect and permit the applied field to penetrate deep into the semiconductor material. Working closely together over the next month, Bardeen and Brattain invented the first successful semiconductor amplifier, called the point-contact transistor, on December 16, 1947. Similar to the World War II crystal rectifiers, this weird-looking device had not one but two closely spaced metal wires jabbing into the surface of a semiconductor—in this case, germanium. The input signal on one of these wires (the emitter) boosted the conductivity of the germanium beneath both of them, thus modulating the output signal on the other wire (the collector). Observers present at a demonstration of this device the following week could hear amplified voices in the earphones that it powered. Shockley later called this invention a “magnificent Christmas present” for the farsighted company, which had supported the research program that made this breakthrough.

      Not to be outdone by members of his own group, Shockley conceived yet another way to fabricate a semiconductor amplifier the very next month, on January 23, 1948. His junction transistor was basically a three-layer sandwich of germanium or silicon in which the adjacent layers would be doped with different impurities to induce distinct electrical characteristics. An input signal entering the middle layer—the “meat” of the semiconductor sandwich—determined how much current flowed from one end of the device to the other under the influence of an applied voltage. Shockley's device is often called the bipolar junction transistor because its operation requires that the negatively charged electrons and their positively charged counterparts (the holes corresponding to an absence of electrons in the crystal lattice) coexist briefly in the presence of one another.

      The name transistor, a combination of transfer and resistor, was coined for these devices in May 1948 by Bell Labs electrical engineer John Robinson Pierce (Pierce, John Robinson), who was also a science-fiction author in his spare time. A month later Bell Labs announced the revolutionary invention in a press conference held at its New York City headquarters, heralding Bardeen, Brattain, and Shockley as the three coinventors of the transistor. The three were eventually awarded the Nobel Prize for Physics for their invention.

      Although the point-contact transistor was the first transistor invented, it faced a difficult gestation period and was eventually used only in a switch made for the Bell telephone system. Manufacturing them reliably and with uniform operating characteristics proved a daunting problem, largely because of hard-to-control variations in the metal-to-semiconductor point contacts.

      Shockley had foreseen these difficulties in the process of conceiving the junction transistor, which he figured would be much easier to manufacture. But it still required more than three years, until mid-1951, to resolve its own development problems. Bell Labs scientists, engineers, and technicians first had to find ways to make ultrapure germanium and silicon, form large crystals of these elements, dope them with narrow layers of the required impurities, and attach delicate wires to these layers to serve as electrodes. In July 1951 Bell Labs announced the successful invention and development of the junction transistor, this time with only Shockley in the spotlight.

Commercialization

      Commercial transistors began to roll off production lines during the 1950s, after Bell Labs licensed the technology of their production to other companies, including General Electric (General Electric Co.), Raytheon (Raytheon Company), RCA (RCA Corporation), Sylvania, and Transitron Electronics. Transistors found ready applications in lightweight devices such as hearing aids and portable radios. Texas Instruments Inc. (Texas Instruments Incorporated), working with the Regency Division of Industrial Development Engineering Associates, manufactured the first transistor radio in late 1954. Selling for $49.95, the Regency TR-1 employed four germanium junction transistors in a multistage amplifier of radio signals. The very next year a new Japanese company, Sony, introduced its own transistor radio and began to corner the market for this and other transistorized consumer electronics.

      Transistors also began replacing vacuum tubes in the digital computers manufactured by IBM (International Business Machines Corporation), Control Data, and other companies. “It seems to me that in these robot brains the transistor is the ideal nerve cell,” Shockley had observed in a 1949 radio interview. “The advantage of the transistor is that it is inherently a small-size and low-power device,” noted Bell Labs circuit engineer Robert Wallace early in the 1950s. “This means you can pack a large number of them in a small space without excessive heat generation and achieve low propagation delays. And that's what you need for logic applications. The significance of the transistor is not that it can replace the tube but that it can do things the vacuum tube could never do!” After 1955 IBM started purchasing germanium transistors from Texas Instruments to employ in its computer circuits. By the end of the 1950s, bipolar junction transistors had almost completely replaced electron tubes in computer applications.

Silicon transistors

      During the 1950s, meanwhile, scientists and engineers at Bell Labs and Texas Instruments were developing advanced technologies needed to produce silicon transistors. Because of its higher melting temperature and greater reactivity, silicon was much more difficult to work with than germanium, but it offered major prospects for better performance, especially in switching applications. Germanium transistors make leaky switches; substantial leakage currents can flow when these devices are supposedly in their off state. Silicon transistors have far less leakage. In 1954 Texas Instruments produced the first commercially available silicon junction transistors and quickly dominated this new market—especially for military applications, in which their high cost was of little concern.

      In the mid-1950s Bell Labs focused its transistor-development efforts around new diffusion technologies, in which very narrow semiconductor layers—with thicknesses measured in microns, or millionths of a metre—are prepared by diffusing impurity atoms into the semiconductor surface from a hot gas. Inside a diffusion furnace the impurity atoms penetrate more readily into the silicon or germanium surface; their penetration depth is controlled by varying the density, temperature, and pressure of the gas as well as the processing time. (See integrated circuit: Fabricating ICs (integrated circuit).) For the first time, diodes and transistors produced by these diffusion implantation processes functioned at frequencies above 100 megahertz (100 million cycles per second). These diffused-base transistors could be used in receivers and transmitters for FM radio and television, which operate at such high frequencies.

      Another important breakthrough occurred at Bell Labs in 1955, when Carl Frosch and Link Derick developed a means of producing a glassy silicon dioxide outer layer on the silicon surface during the diffusion process. This layer offered transistor producers a promising way to protect the silicon underneath from further impurities once the diffusion process was finished and the desired electrical properties had been established.

      Texas Instruments, Fairchild Semiconductor Corporation, and other companies took the lead in applying these diffusion technologies to the large-scale manufacture of transistors. At Fairchild, physicist Jean Hoerni developed the planar manufacturing process, whereby the various semiconductor layers and their sensitive interfaces are embedded beneath a protective silicon dioxide outer layer. The company was soon making and selling planar silicon transistors, largely for military applications. Led by Robert Noyce (Noyce, Robert) and Gordon E. Moore (Moore, Gordon E.), Fairchild's scientists and engineers extended this revolutionary technique to the manufacture of integrated circuits (integrated circuit).

      In the late 1950s Bell Labs researchers developed ways to use the new diffusion technologies to realize Shockley's original 1945 idea of a field-effect transistor (FET). To do so, they had to overcome the problem of surface-state electrons, which would otherwise have blocked external electric fields from penetrating into the semiconductor. They succeeded by carefully cleaning the silicon surface and growing a very pure silicon dioxide layer on it. This approach reduced the number of surface-state electrons at the interface between the silicon and oxide layers, permitting fabrication of the first successful field-effect transistor in 1960 at Bell Labs—which, however, did not pursue its development any further.

      Refinements of the FET design by other companies, especially RCA and Fairchild, resulted in the metal-oxide-semiconductor field-effect transistor (MOSFET) during the early 1960s. The key problems to be solved were the stability and reliability of these MOS transistors, which relied upon interactions occurring at or near the sensitive silicon surface rather than deep inside. The two firms began to make MOS transistors commercially available in late 1964.

 In early 1963 Frank Wanlass at Fairchild developed the complementary MOS (CMOS) transistor circuit, based on a pair of MOS transistors (see figure—>). This approach eventually proved ideal for use in integrated circuits because of its simplicity of production and very low power dissipation during standby operation. Stability problems continued to plague MOS transistors, however, until researchers at Fairchild developed solutions in the mid-1960s. By the end of the decade, MOS transistors were beginning to displace bipolar junction transistors in microchip manufacturing. Since the late 1980s CMOS has been the technology of choice for digital applications, while bipolar transistors are now used primarily for analog and microwave devices.

Transistor principles

The junction (p-n junction)

      The operation of junction transistors, as well as most other semiconductor devices, depends heavily on the behaviour of electrons and holes at the interface between two dissimilar layers, known as a p-n junction. Discovered in 1940 by Bell Labs electrochemist Russell Ohl, p-n junctions are formed by adding two different impurity elements to adjacent regions of germanium or silicon. Atoms of elements from the fifth column of the periodic table (which possess five valence electrons), such as phosphorus or arsenic, contribute an electron that has no natural resting place within the crystal lattice. These excess electrons are therefore loosely bound and relatively free to roam about, acting as charge carriers that can conduct electrical current. Atoms of elements from the third column (which have three valence electrons), such as boron or aluminum, induce a deficit of electrons when added as impurities, effectively creating “holes” in the lattice. These positively charged quantum mechanical entities are also fairly free to roam around and conduct electricity. Under the influence of an electric field, the electrons and holes move in opposite directions. During and immediately after World War II, chemists and metallurgists at Bell Labs perfected techniques of adding impurities to high-purity silicon and germanium to induce the desired electron-rich layer (known as the n-layer) and the electron-poor layer (known as the p-layer) in these semiconductors, as described in the section Development of transistors (transistor).

  A p-n junction acts as a rectifier, similar to the old point-contact crystal rectifiers, permitting easy flow of current in only a single direction. If no voltage is applied across the junction, electrons and holes will gather on opposite sides of the interface to form a depletion layer that will act as an insulator between the two sides (see figure—>). A negative voltage applied to the n-layer will drive the excess electrons within it toward the interface, where they will combine with the positively charged holes attracted there by the electric field. Current will then flow easily (see figure—>). If instead a positive voltage is applied to the n-layer, the resulting electric field will draw electrons away from the interface, so combinations of them with holes will occur much less often. In this case current will not flow (other than tiny leakage currents). Thus, electricity will flow in only one direction through a p-n junction.

Junction transistors

 Shortly after his colleagues John Bardeen (Bardeen, John) and Walter H. Brattain (Brattain, Walter H.) invented their point-contact device, Bell Labs physicist William B. Shockley (Shockley, William B.) recognized that these rectifying characteristics might also be used in making a junction transistor. In a 1949 paper Shockley explained the physical principles behind the operation of these junctions and showed how to use them in a three-layer—n-p-n or p-n-p—device that could act as a solid-state amplifier or switch. Electric current would flow from one end to the other, with the voltage applied to the inner layer governing how much current rushed by at any given moment. In the n-p-n junction transistor (see figure—> for a modern version), for example, electrons would flow from one n-layer through the inner p-layer to the other n-layer. Thus, a weak electrical signal applied to the inner, base layer would modulate the current flowing through the entire device. For this current to flow, some of the electrons would have to survive briefly in the presence of holes; in order to reach the second n-layer, they could not all combine with holes in the p-layer. Such bipolar operation was not at all obvious when Shockley first conceived his junction transistor. Experiments with increasingly pure crystals of silicon and germanium showed that it indeed occurred, making bipolar junction transistors possible.

      To achieve bipolar operation, it also helps that the base layer be narrow, so that electrons (in n-p-n transistors) and holes (in p-n-p) do not have to travel very far in the presence of their opposite numbers. Narrow base layers also promote high-frequency operation of junction transistors: the narrower the base, the higher the operating frequency. That is a major reason why there was so much interest in developing diffused-base transistors during the 1950s, as described in the section Silicon transistors (transistor). Their microns-thick bases permitted transistors to operate above 100 megahertz (100 million cycles per second) for the first time.

MOS-type transistors

 A similar principle applies to metal-oxide-semiconductor (MOS) transistors, but here it is the distance between source and drain that largely determines the operating frequency. In an n-channel MOS (NMOS) transistor (see figure—>), for example, the source and the drain are two n-type regions that have been established in a piece of p-type semiconductor, usually silicon. Except for the two points at which metal leads contact these regions, the entire semiconductor surface is covered by an insulating oxide layer. The metal gate, usually aluminum, is deposited atop the oxide layer just above the gap between source and drain. If there is no voltage (or a negative voltage) upon the gate, the semiconductor material beneath it will contain excess holes, and very few electrons will be able to cross the gap, because one of the two p-n junctions will block their path. Therefore, no current will flow in this configuration—other than unavoidable leakage currents. If the gate voltage is instead positive, an electric field will penetrate through the oxide layer and attract electrons into the silicon layer (often called the inversion layer) directly beneath the gate. Once this voltage exceeds a specific threshold value, electrons will begin flowing easily between source and drain. The transistor turns on.

      Analogous behaviour occurs in a p-channel MOS transistor, in which the source and the drain are p-type regions formed in n-type semiconductor material. Here a negative voltage above a threshold induces a layer of holes (instead of electrons) beneath the gate and permits a current of them to flow from source to drain. For both n-channel and p-channel MOS (also called NMOS and PMOS) transistors, the operating frequency is largely governed by the speed at which the electrons or holes can drift through the semiconductor material divided by the distance from source to drain. Because electrons have mobilities through silicon that are about three times higher than holes, NMOS transistors can operate at substantially higher frequencies than PMOS transistors. Small separations between source and drain also promote high-frequency operation, and extensive efforts have been devoted to reducing this distance.

 In the 1960s Frank Wanlass of Fairchild Semiconductor recognized that combinations of an NMOS and a PMOS transistor would draw extremely little current in standby operation—just the tiny, unavoidable leakage currents. These CMOS, or complementary metal-oxide-semiconductor, transistor circuits consume significant power only when the gate voltage exceeds some threshold and a current flows from source to drain (see figure—>). Thus, they can serve as very low-power devices, often a million times lower than the equivalent bipolar junction transistors. Together with their inherent simplicity of fabrication, this feature of CMOS transistors has made them the natural choice for manufacturing microchips, which today cram millions of transistors into a surface area smaller than a fingernail. In such cases the waste heat generated by the component's power consumption must be kept to an absolute minimum, or the chips will simply melt.

Field-effect transistors

 Another kind of unipolar transistor, called the metal-semiconductor field-effect transistor (MESFET), is particularly well suited for microwave and other high-frequency applications because it can be manufactured from semiconductor materials with high electron mobilities that do not support an insulating oxide surface layer. These include compound semiconductors such as germanium-silicon and gallium arsenide. A MESFET is built much like a MOS transistor (see figure—>) but with no oxide layer between the gate and the underlying conduction channel. Instead, the gate makes a direct, rectifying contact with the channel, which is generally a thin layer of n-type semiconductor supported underneath by an insulating substrate. A negative voltage on the gate induces a depletion layer just beneath it that restricts the flow of electrons between source and drain. The device acts like a voltage-controlled resistor; if the gate voltage is large enough, it can block this flow almost completely. By contrast, a positive voltage on the gate encourages electrons to traverse the channel.

      To improve MESFET performance even further, advanced devices known as heterojunction field-effect transistors have been developed, in which p-n junctions are established between two slightly dissimilar semiconductor materials, such as gallium arsenide and aluminum gallium arsenide. By properly controlling the impurities in the two substances, a high-conductivity channel can be formed at their interface, promoting the flow of electrons through it. If one semiconductor is a high-purity material, its electron mobility can be large, resulting in a high operating frequency for this kind of transistor. (The electron mobility of gallium arsenide, for example, is five times that of silicon.) Heterojunction MESFETs are increasingly used for microwave applications such as cellular telephone systems.

Transistors and Moore's law

      In 1965, four years after Fairchild Semiconductor Corporation and Texas Instruments Inc. (Texas Instruments Incorporated) marketed their first integrated circuits, Fairchild research director Gordon E. Moore (Moore, Gordon E.) made a prediction in a special issue of Electronics magazine. Observing that the total number of components in these circuits had roughly doubled each year, he blithely extrapolated this annual doubling to the next decade, estimating that microcircuits of 1975 would contain an astounding 65,000 components per chip.

 History proved Moore correct. His bold extrapolation has since become enshrined as Moore's law—though its doubling period was lengthened to 18 months in the mid-1970s (see figure—>). What has made this dramatic explosion in circuit complexity possible is the steadily shrinking size of transistors over the decades. Measured in millimetres in the late 1940s, the dimensions of a typical transistor are now more commonly expressed in tenths of a micron, a reduction factor of over 10,000. Submicron transistor features were attained during the 1980s, when dynamic random-access memory (DRAM) chips began offering megabit storage capacities. At the dawn of the 21st century, these features approached 0.1 micron across, which allowed the manufacture of gigabit memory chips and microprocessors that operate at gigahertz frequencies.

      As the size of transistors has shrunk, their cost has plummeted correspondingly from tens of dollars apiece to thousandths of a penny. As Moore was fond of saying, every year more transistors are produced than raindrops over California, and it costs less to make one than to print a single character on this page. They are by far the most common human artifact on the planet. Deeply embedded in everything electronic, transistors permeate modern life almost as thoroughly as molecules permeate matter. Cheap, portable, and reliable equipment based on this remarkable device can be found in almost any village and hamlet in the world. This tiny invention, by making possible the Information Age, has transformed the world into a truly global society, making it a far more intimately connected place than ever before.

Michael Riordan

Additional Reading

Michael Riordan and Lillian Hoddeson, Crystal Fire: The Birth of the Information Age (1997; also published as Crystal Fire: The Invention of the Transistor and the Birth of the Information Age, 1998), describes the fascinating science and engineering that led to the invention and development of the transistor. Ross Knox Bassett, To the Digital Age: Research Labs, Start-Up Companies, and the Rise of MOS Technology (2002), presents the corporate and technical history of the development of MOS transistors during the 1960s. Robert Buderi, The Invention That Changed the World: How a Small Group of Radar Pioneers Won the Second World War and Launched a Technological Revolution (1996; also published as The Invention That Changed the World: The Story of Radar from War to Peace, 1998), examines the development of radar and how it fueled postwar electronics.

* * *