—sawer, n. —sawlike, adj./saw/, n., v., sawed, sawed or sawn, sawing.n.1. a tool or device for cutting, typically a thin blade of metal with a series of sharp teeth.2. any similar tool or device, as a rotating disk, in which a sharp continuous edge replaces the teeth.v.t.3. to cut or divide with a saw.4. to form by cutting with a saw.5. to make cutting motions as if using a saw: to saw the air with one's hands.6. to work (something) from side to side like a saw.v.i.7. to use a saw.8. to cut with or as if with a saw.9. to cut as a saw does.10. saw wood, Informal. to snore loudly while sleeping.[bef. 1000; (n.) ME sawe, OE saga, *sagu; c. D zaag, ON sog; akin to G Säge saw, L secare to cut (see SECTION), OE seax knife, SAX2; (v.) ME sawen, deriv. of the n.]saw2/saw/, v.pt. of see1.saw3/saw/, n.a sententious saying; maxim; proverb: He could muster an old saw for every occasion.
* * *Tool for cutting solid materials to prescribed lengths or shapes.Most saws take the form of a thin metal strip with teeth on one edge or a thin metal disk with teeth on the edge. The teeth are usually set to alternate sides so that the kerf (groove) cut by the saw is wider than the thickness of the saw; the saw blade can thus move freely in the groove without binding. Thin-strip saws are used in various ways in both hand and machine operations; circular, or disk, saws are always machine powered (see sawing machine, machine tool).
* * *▪ tooltool for cutting solid materials to prescribed lengths or shapes. Most saws take the form of a thin metal strip with teeth on one edge or a thin metal disk with teeth on the periphery. Usually the teeth are “set” (bent) to alternate sides so that the kerf (groove) cut by the saw is wider than the thickness of the saw. This prevents binding between the cut surfaces and the sides of the saw. The thin-strip saws are used in a variety of arrangements for both hand and machine operation, while circular, or disk, saws are invariably machine powered.The hand hacksaw has a U-shaped frame and blades 20 to 30 cm (8 to 12 inches) long, 1.25 cm (0.5 inch) wide, and 0.06 cm (0.025 inch) thick that close the U and are placed under tension by a screw adjustment in the handle. This saw is one of the most common tools in a machine shop and is used for cutting off solid parts held in a vise. Saws of this type are also used by butchers for cutting bones. For cutting curves and other irregular shapes in wood or other materials, the coping, or jeweler's, saw, which is basically a hacksaw with a deeper U-shaped frame and a much narrower blade, is well-suited.The power jigsaw, or scroll saw, does mechanically the same irregular cutting as the hand coping saw. The straight, narrow blade is mounted vertically between a pulsating lower shaft and a reciprocating upper shaft, which together move the blade rapidly up and down. Power hacksaws, driven by electric motors, are indispensable in any general-purpose machine shop or tool room; they are most often used for cutting metal. The blade is much wider and thicker and the frame much heavier than those of a hand hacksaw. The frame, carrying the blade, moves back and forth, cutting in one direction only, while a slight feeding pressure or weight automatically presses the saw against the work.The vertical bandsaw blade is an endless narrow metal strip, with teeth along one edge, that runs around two large motorized pulleys or wheels that are mounted on a frame so that one is directly above the other. The blade passes through the table on which the work is laid. Blades are available with various sizes of teeth, and on most machines the blade speed can be varied to suit the material being cut.Among the saws that are neither loops nor disks are three of the most common hand saws used by the carpenter: the ripsaw, the crosscut saw, and the backsaw. The first two have roughly triangular blades about 50 cm (20 inches) long, 10 cm (4 inches) wide at the handle, and tapering to about 5 cm (2 inches) at the opposite end. Ripsaws are used for cutting wood with the grain, crosscut saws for cutting across the grain. The main difference between the saws is in the way the teeth are ground. The ripsaw teeth have cutting edges that are at 90° to the blade and act like a row of chisels; the crosscut has knifelike teeth that are set to alternate sides and cut two parallel lines on each side of the kerf, so that the wood in between is broken up. The backsaw is a crosscut saw with a rectangular blade and heavy steel backing along the side opposite the teeth; this keeps the blade perfectly straight. It is usually guided by an attachment that keeps it level at all times and maintains it in the proper direction when making angular cuts.Among the machines utilizing a rotating steel disk with peripheral teeth, the radial-arm saw is one of the most useful. The motor-driven blade is manually drawn along a horizontally set shaft or pipe, called a radial arm, that is itself supported by a vertical column attached to a heavy base. The motor-blade unit is free to move back and forth along the arm and can be adjusted to different heights by movement of the radial arm on its vertical support. The motor-blade unit can also be pivoted to make angular and ripping cuts. The work is laid on a wooden table on top of the base, and the motor-blade unit is manually moved across it, cutting as it goes. The table saw (or stationary circular saw) consists of a circular saw that can be raised and tilted, protruding through a slot in a horizontal metal table on which the work can be laid and pushed into contact with the saw. This saw is one of the basic machines in any woodworking shop; with blades of sufficient hardness, table saws can also be used for cutting metal bars. For heavy cutting-off operations the circular or cold saw is used extensively in steel plants such as cold-drawing mills or where large quantities of bars and shafts are cut. In operation, the saw carriage is fed slowly into the work.The portable electric circular saw, with the blade attached to a motor shaft, is probably the most commonly used saw, particularly by home handymen. With the proper blade it can cut almost any material—wood, metals, plastics, fibreglass, cement block, slate, and brick. On wood it can rip, crosscut, and make angle cuts. The sabre saw, which is basically a portable jigsaw, moves up and down and may have a stroke of as much as 2.5 cm (1 inch). It can rip, crosscut, and make angle cuts. The portable chain saw has practically replaced the woodman's axe and the two-man hand saw for felling trees. It consists of a thin metal frame supporting a steel roller chain carrying saw teeth attached at intervals along its length; the teeth are slightly wider than the chain to prevent binding of the chain body and the material being cut. An electric motor or a small gasoline engine causes the chain sprocket to rotate, drawing the chain around with it at a high rate of speed.
* * *