/muy"kreuh skohp'/, n.
1. an optical instrument having a magnifying lens or a combination of lenses for inspecting objects too small to be seen or too small to be seen distinctly and in detail by the unaided eye.
2. (cap.) Astron. the constellation Microscopium.
[1650-60; < NL microscopium. See MICRO-, -SCOPE]

* * *

Instrument that produces enlarged images of small objects, allowing them to be viewed at a scale convenient for examination and analysis.

Formed by various means, the image is received by direct imaging, electronic processing, or a combination of these methods. The most familiar type of microscope is the optical, or light, microscope, in which lenses are used to form the image. Other types of microscopes use the wave nature of various physical processes, the most important being the electron microscope (see electron microscopy), which uses a beam of electrons in its image formation. Crude microscopes date to the mid-15th century, but not until 1674 were the powerful microscopes of A. van Leeuwenhoek able to detect phenomena as small as protozoa.

* * *

  instrument that produces enlarged images of small objects, allowing the observer an exceedingly close view of minute structures at a scale convenient for examination and analysis. The image may be enlarged by many wave-forms, including optical, acoustic, X-ray, or electron beam, and it is received by direct or digital imaging or by a combination of these methods. The microscope may provide a dynamic image (as with conventional optical instruments) or one that is time-dependent (as with conventional scanning electron microscopes).

      The magnifying power of a microscope is an expression of the number of times the object being examined appears to be enlarged and is a dimensionless ratio. It is usually expressed in the form 10× (for an image magnified 10-fold), sometimes wrongly spoken as “ten eks”—as though the × were an algebraic symbol—rather than the correct form, “ten times.” The resolution of a microscope is a measure of the smallest detail of the object that can be observed. Resolution is expressed in linear units, usually micrometres (micrometre) (μm).

      The most familiar type of microscope is the optical or light microscope, in which glass lenses (lens) are used to form the image. Optical microscopes can be simple, consisting of a single lens, or compound, consisting of several optical components in line. Present-day simple optical magnifiers may have magnifying powers ranging from 1 to 50×. Compound optical microscopes have magnifying powers ranging from about 20 to 2,000× and can resolve features as small as 0.2 μm. Images may be captured by photographic means, although digital systems now allow the production of inexpensive optical microscopes that display their images directly on a computer screen.

 Other types of microscopes use the wave nature of various physical processes, the most important being the electron microscope, which uses a beam of electrons in its image formation. The transmission electron microscope (microscope) (TEM) has magnifying powers of more than 1,000,000×. TEMs form images of thin specimens, typically sections, in a near vacuum. A scanning electron microscope (microscope) (SEM), which creates a reflected image of relief in a contoured specimen, usually has a lower resolution than a TEM but can show solid surfaces in a way that the conventional electron microscope cannot. There are also microscopes that use lasers (laser), sound, or X-rays. The scanning tunneling microscope (microscope) (STM), which can create images of atoms, and the environmental scanning electron microscope (microscope) (ESEM), which generates images using electrons of specimens in a gaseous environment, use other physical effects that further extend the types of objects that can be examined.

Optical microscopes

      The concept of magnification has long been known. About 1267 English philosopher Roger Bacon (Bacon, Roger) wrote in Perspectiva, “[We] may number the smallest particles of dust and sand by reason of the greatness of the angle under which we may see them,” and in 1538 Italian physician Girolamo Fracastoro (Fracastoro, Girolamo) wrote in Homocentrica, “If anyone should look through two spectacle glasses, one being superimposed on the other, he will see everything much larger.”

 Three Dutch spectacle makers—Hans Jansen, his son Zacharias Jansen, and Hans Lippershey (Lippershey, Hans)—have received credit for inventing the compound microscope about 1590. The first portrayal of a microscope was drawn about 1631 in the Netherlands. It was clearly of a compound microscope, with an eyepiece and an objective lens. This kind of instrument, which came to be made of wood and cardboard, often adorned with polished fish skin, became increasingly popular in the mid-17th century and was used by the English natural philosopher Robert Hooke (Hooke, Robert) to provide regular demonstrations for the new Royal Society. These demonstrations commenced in 1663, and two years later Hooke published a folio volume titled Micrographia, which introduced a wide range of microscopic views of familiar objects (fleas, lice, and nettles among them). In this book he coined the term cell.

 Hidden in the unnumbered pages of Micrographia's preface is a description of how a single high-powered lens could be made into a serviceable microscope, and it was using this design that the Dutch civil servant Antonie van Leeuwenhoek (Leeuwenhoek, Antonie van) began his pioneering observations of freshwater microorganisms in the 1670s. He made his postage-stamp-sized microscopes by hand, and the best of them could resolve details around 0.7 m. His fine specimens discovered in excellent condition at the Royal Society more than three centuries later prove what a great technician he was. Using his simple microscope, Leeuwenhoek effectively launched microbiology in 1674, and single-lensed microscopes remained popular until the 1850s. In 1827 they were used by Scottish botanist Robert Brown (Brown, Robert) to demonstrate the ubiquity of the cell nucleus, a term he coined in 1831.

      Simple microscopes using single lenses (lens) can generate fine images; however, they can also produce spurious colours due to chromatic aberration, in which different wavelengths of light do not come to the same focus. The aberrations were worse in the compound microscopes of the time, because the lenses magnified the aberrations at least as much as they magnified the images. Although the compound microscopes were beautiful objects that conferred status on their owners, they produced inferior images. In 1733 the amateur English optician Chester Moor Hall (Hall, Chester Moor) found by trial and error that a combination of a convex crown-glass (crown glass) lens and a concave flint-glass (flint glass) lens could help to correct chromatic aberration in a telescope, and in 1774 Benjamin Martin of London produced a pioneering set of colour-corrected lenses for a microscope.

      The appearance of new varieties of optical glasses encouraged continued development of the microscope in the 19th century, and considerable improvements were made in understanding the geometric optics of image formation. The concept of an achromatic (non-colour-distorting) microscope objective was finally introduced in 1791 by Dutch optician Francois Beeldsnijder, and the English scientist Joseph Jackson Lister (Lister, Joseph Jackson) in 1830 published a work describing a theoretical approach to the complete design of microscope objectives. The physics of lens construction was examined by German physicist Ernst Abbe (Abbe, Ernst). In 1868 he invented an apochromatic system of lenses, which had even better colour correction than achromatic lenses, and in 1873 he published a comprehensive analysis of lens theory. Light microscopes were produced in the closing quarter of the 19th century that reached the effective limits of optical microscopy. Subsequent instruments, such as phase-contrast microscopes (microscope), interference microscopes (microscope), and confocal microscopes (microscope), solved specific problems that had previously made studying important objects such as living cells very difficult.

The simple microscope
 The simple microscope consists of a single or compound lens traditionally called a loupe. The most familiar present-day example is a reading or magnifying glass. Higher-magnification lenses can be worn around the neck packaged in a cylindrical form that can be held in place immediately in front of the eye. These are generally referred to as eye loupes or jewelers' lenses.

      A magnifier permits the user to place the eye close to an object of interest and retain a focused image. The closer the object is to the eye, the larger the angle that it subtends at the eye, and thus the larger the object appears. If an object is brought too close, however, the eye can no longer form a clear image. The use of the magnifying lens between the observer and the object enables the formation of a “virtual image” that can be viewed in comfort. To obtain the best possible image, the magnifier should be placed directly in front of the eye. The object of interest is then brought toward the eye until a clear image of the object is seen.

      Without lenses, the highest possible magnification is when the object is brought to the closest position at which a clear virtual image is observed. For most people, this image distance is about 25 cm (10 inches). As people age, the nearest point of distinct vision recedes to greater distances, thus making a magnifier a useful adjunct to vision for older people.

      The magnifying power, or extent to which the object being viewed appears enlarged, and the field of view, or size of the object that can be viewed, are related by the geometry of the optical system. A working value for the magnifying power of a lens can be found by dividing the least distance of distinct vision by the lens' focal length, which is the distance from the lens to the plane at which the incoming light is focused. Thus, for example, a lens with a least distance of distinct vision of 25 cm and a focal length of 5 cm (2 inches) will have a magnifying power of about 5×.

      If the diameter of the magnifying lens is sufficient to fill or exceed the diameter of the pupil of the eye, the virtual image that is viewed will appear to be of substantially the same brightness as the original object. The field of view of the magnifier will be determined by the extent to which the magnifying lens exceeds this working diameter and also by the distance separating the lens from the eye. The clarity of the magnified virtual image will depend upon the aberrations present in the lens, its contour, and the manner in which it is used.

   Various aberrations influence the sharpness or quality of the image. Chromatic aberrations (chromatic aberration) produce coloured fringes about the high-contrast regions of the image, because longer wavelengths of light (such as red) are brought to focus in a plane slightly farther from the lens than shorter wavelengths (such as blue). Spherical aberration produces an image in which the centre of the field of view is in focus when the periphery may not be and is a consequence of using lenses with spherical (rather than nonspherical, or aspheric) surfaces. Distortion produces curved images from straight lines in the object. The type and degree of distortion visible is intimately related to the possible spherical aberration in the magnifier and is usually most severe in high-powered lenses.

      The aberrations of a lens increase as the relative aperture (i.e., the working diameter divided by the focal length) of the lens is increased. Therefore, the aberrations of a lens whose diameter is twice the focal length will be worse than those of a lens whose diameter is less than the focal length. There is thus a conflict between a short focal length, which permits a high magnifying power but small field of view, and a longer focal length, which provides a lower magnifying power but a larger linear field of view. (Leeuwenhoek's high-powered lenses of the 1670s had a focal length—and thus a working distance—of a few millimetres. This made them difficult to use, but they provided remarkable images that were not bettered for a century.)

Types of magnifiers
      There are several types of magnifiers available. The choice of an optical design for a magnifier depends upon the required power and the intended application of the magnifier.

      For low powers, about 2–10×, a simple double convex lens is applicable. (Early simple microscopes such as Leeuwenhoek's magnified up to 300×.) The image can be improved if the lens has specific aspheric surfaces, as can be easily obtained in a plastic molded lens. A reduction of distortion is noted when an aspheric lens is used, and the manufacture of such low-power aspheric plastic magnifiers is a major industry. For higher powers of 10–50×, there are a number of forms for magnifiers in which the simple magnifier is replaced by a compound lens made up of several lenses mounted together.

      A direct improvement in the distortion that may be expected from a magnifier can be obtained by the use of two simple lenses, usually plano-convex (flat on one side, outward-curved on the other, with the curved surfaces facing each other). This type of magnifier is based upon the eyepiece of the Huygenian telescope, in which the lateral chromatic aberration is corrected by spacing the elements a focal length apart. Since the imaging properties are provided and shared by two components, the spherical aberration and the distortion of the magnifier are greatly reduced over those of a simple lens of the same power.

      A Coddington lens combines two lens elements into a single thick element, with a groove cut in the centre of the element to select the portion of the imaging light with the lowest aberrations. This was a simple and inexpensive design but suffers from the requirement that the working distance of the magnifier be very short.

      More-complex magnifiers, such as the Steinheil or Hastings forms, use three or more elements to achieve better correction for chromatic aberrations and distortion. In general, a better approach is the use of aspheric surfaces and fewer elements.

      Mirrors (mirror) are also used. Reflecting microscopes, in which the image is magnified through concave mirrors rather than convex lenses, were brought to their peak of perfection by British physicist C.R. Burch, who made a series of giant instruments that used ultraviolet (ultraviolet radiation) rays. There is no chromatic aberration using a reflector, and distortion and spherical aberration are controlled through the introduction of a carefully contoured aspheric magnifying mirror. Present-day reflecting microscopes are confined to analytical instruments using infrared (infrared radiation) rays.

The compound microscope
      The limitations on resolution (and therefore magnifying power) imposed by the constraints of a simple microscope can be overcome by the use of a compound microscope, in which the image is relayed by two lens arrays. One of them, the objective, has a short focal length and is placed close to the object being examined. It is used to form a real image in the front focal plane of the second lens, the eyepiece or ocular. The eyepiece forms an enlarged virtual image that can be viewed by the observer. The magnifying power of the compound microscope is the product of the magnification of the objective lens and that of the eyepiece.

      In addition to these two lens arrays, a compound microscope consists of a body tube, in which the lenses can be housed and kept an appropriate distance apart; a condenser lens that lies beneath the specimen stage and focuses light upon the specimen; and an illumination system, which either transmits light through or reflects light from the object being examined. A method for focusing the microscope, usually with coarse and fine focusing controls, must also be provided.

      The basic form of a compound microscope is monocular: a single tube is used, with the objective at one end and a single eyepiece at the other. In order to permit viewing with two eyes and thereby increase comfort and acuity, a single objective can be employed in a binocular tube fitted with a matched pair of eyepieces; beam-splitting prisms (prism) are used to send half of the light from the image formed by the objective to each eye. These prisms are mounted in a rotating mechanical assembly so that the separation between the eyepieces can be made to match the required interpupillary distance for the observer. A true stereoscopic microscope is configured by using two objectives and two eyepieces, enabling each eye to view the object separately, making it appear three-dimensional.

      There are some obvious geometric limitations that apply to the design of microscope optics. The attainable resolution, or the smallest distance at which two points can be seen as separate when viewed through the microscope, is the first important property. This is generally set by the ability of the eye to discern detail, as well as by the basic physics of image formation.

      The eye's ability to discern detail is determined by several factors, including the level of illumination and the degree of contrast between light and dark regions on the object. Under reasonable light conditions, a normal eye with good visual acuity is capable of seeing two high-contrast points if they subtend a visual angle of at least one arc minute in size. Thus, at a nominal viewing distance of 25 cm (10 inches), the points must be at least 0.1 mm (0.004 inch) apart for the eye to see them as separate. With a simple magnifier of 10×, an observer can see two points separated by perhaps 0.01 mm (0.0004 inch); and with a compound microscope magnifying 100×, one might expect the observer to be able to distinguish two points only 0.001 mm (0.00004 inch) apart. However, an additional complication arises for the high magnifications encountered in a compound microscope. When the dimensions to be resolved approach the wavelength of light, consideration must be given to the effect of diffraction upon the eye's ability to resolve details upon objects (see below The theory of image formation (microscope)).

      The resolution and the light-collecting capability of the microscope are determined by the numerical aperture (N.A.) of the objective. The N.A. is defined as the sine of half the angle of the cone of light from each point of the object that can be accepted by the objective multiplied by the refractive index (R.I.) of the medium in which the object is immersed. Thus, the N.A. increases as the lens becomes larger or the R.I. increases. Typical values for microscope objective N.A.'s range from 0.1 for low-magnification objectives to 0.95 for dry objectives and 1.4 for oil-immersion objectives. A dry objective is one that works with the air between the specimen and the objective lens. An immersion objective requires a liquid, usually a transparent oil of the same R.I. as glass, to occupy the space between the object and the front element of the objective.

      The limit of resolution is set by the wavelength of light and the N.A. The resolution can be improved either by increasing the N.A. of a lens or by using light with a shorter wavelength. In an immersion objective, the effective wavelength of the light is reduced by the index of refraction of the media within which the object being examined resides. The use of immersion imaging techniques in microscopy improves the resolution capabilities of the microscope.

Mechanical components
 The microscope body tube separates the objective and the eyepiece and assures continuous alignment of the optics. It is a standardized length, anthropometrically related to the distance between the height of a bench or tabletop (on which the microscope stands) and the position of the seated observer's eyes. It is typically fitted with a rotating turret that permits objectives of different powers to be interchanged with the assurance that the image position will be maintained. Traditionally, the length of the body tube has been defined as the distance from the upper end of the objective to the eyepiece end of the tube.

      A standard body-tube length of 160 mm (6.3 inches) has been accepted for most uses. (Metallographic microscopes have a 250-mm [10-inch] body tube.) Microscope objectives are designed to minimize aberrations at the specified tube length. Use of other distances will affect the aberration balance for high-magnification objectives. Therefore, focusing of the traditional microscope requires moving the objective, the tube, and the eyepiece as a rigid unit. To achieve this, the entire tube is fitted with a rack-and-pinion mechanism that allows it, together with the objective and the eyepiece, to be moved toward or away from the specimen.

      The specimen is usually mounted on a glass slide. Routine microscope slides were fixed at 3 × 1 inches during the Victorian era and are still produced at the metric equivalent of those dimensions (7.5 × 2.5 cm) today. The specimen, usually immersed in a material with an R.I. that matches that of the slide, is covered with a thin cover slip. The mechanical stage on which the slide lies is fitted with a pair of controls featuring a rack-and-pinion arrangement. This permits the glass slide to be moved across the stage in two directions, so that different areas of the specimen can be examined. Computer-controlled microscopes track the position of the slide and can return to designated areas of the specimen when required to do so.

      The accuracy with which the focusing and the movement of the slide have to be maintained increases as the depth of focus of the objective decreases. For high-N.A. objectives, this depth of focus can be as small as 1 or 2 μm, which means that the mechanical components must provide stable motion at even smaller increments.

      Several approaches have been introduced to achieve such precise stable motion at reasonable cost. Some designers have eliminated the sliding mechanism of the body tube, incorporating adjustments for the vertical movement needed for focusing, as well as the lateral motion of the object, in a single mechanical system. An alternative approach has been to mount a relay objective doublet of 160 mm (6.3 inches) focal length into the lower end of the tube. This tube lens is designed to accept light from an image created by the objective at infinity. The objective itself is designed to have aberrations corrected for an infinite image distance. An advantage of this approach is that, since the relayed image is at infinity, the microscope objective itself, a very lightweight component, can be moved to effect focusing without upsetting the correction of aberrations.

      In some microscopes the eyepiece is designed as a portion of a zoom lens, which permits continuous variation of the magnification over a limited range without loss of focus. Such microscopes are widely used in industry.

The illumination system
      The illumination system of the standard optical microscope is designed to transmit light through a translucent object for viewing. In a modern microscope it consists of a light source, such as an electric lamp or a light-emitting diode, and a lens system forming the condenser.

      The condenser is placed below the stage and concentrates the light, providing bright, uniform illumination in the region of the object under observation. Typically, the condenser focuses the image of the light source directly onto the plane of the specimen, a technique called critical illumination. Alternatively, the image of the source is focused onto the condenser, which is in turn focused onto the entrance pupil of the microscope objective, a system known as Köhler illumination. The advantage of the latter approach is that nonuniformities in the source are averaged in the imaging process. To obtain optimal use of the microscope, it is important that the light from the source both covers the object and fills the entrance aperture of the objective of the microscope with light.

      Early microscopes had as their condenser a single lens, which was fixed in the end of the instrument facing the lamp (as in barrel microscopes) or mounted below the stage (as in the Bancks microscopes used by Robert Brown, Charles Darwin (Darwin, Charles), and others). More-complex designs followed, their development driven by the peculiarly English obsession of observing fine details on diatom frustules. Achromatic condensers followed, but they are more troublesome to use because they need precise focusing, and the working distance is short.

      Apart from condensers that are matched to specialized objectives (such as phase-contrast systems), others are available for specific applications. Thus, the dark-ground, or dark-field, condenser illuminates specimens against a black background and is eminently applicable to the observation of structures such as bacteria and flagellated cells in water. The use of colour filters, pioneered in the closing years of the 19th century by British microscopist Julius Rheinberg and now known as Rheinberg illumination, allows one to practice a form of dark-ground microscopy in which the background and the specimen are in contrasting colours. Although this technique is of no diagnostic benefit, the results can be spectacularly beautiful.

The objective
      The optics of the microscope objective are defined by the focal length, N.A., and field of view. Objectives that have been corrected for aberrations are further defined by the wavelength requirements and the tube length of the microscope.

      Manufacturers provide objective lenses with standard magnifications usually ranging from 2 to 100×. The focal length of the objective is inversely proportional to the magnification and, in the majority of modern microscopes, equals the tube length (usually 160 mm [6.3 inches]) divided by the magnification. The field of view of the eyepiece is usually set to be a standard size of about 20 mm (0.8 inch) diameter. The field of view of the objective is then set to range from 10 mm (0.4 inch) for an objective with a magnifying power of 2× to 0.2 mm (0.008 inch) for an objective with a magnification of 100×. As a result, the angular field of view is about 7° for all objectives.

aberration correction
      The N.A. and the complexity of the objective increase as the magnification increases. Low-power objectives, of order 2–5×, are generally two-element lenses. Ordinary crown glass and flint glass (optical glasses with, respectively, relatively low and high R.I.'s) can be used to correct for spherical and chromatic aberration.

      For objectives with magnifying powers of 10×, the required N.A. increases to 0.25, and a more complex type of lens is required. Most microscope objectives of this magnification use a separated pair of doublets that share the refractive power. The correction of spherical aberration is readily achieved, but residual chromatic aberration is obtained when normal optical glasses are used for the lens elements. For most optical applications this is not important, but for critical high-magnification objectives (magnifications greater than 25×) this aberration is visible as chromatic blur. The correction of this residual aberration is achieved through the use of special optical glasses whose dispersion properties vary from normal glasses. There are only a few such glasses or crystalline materials that are useful for this purpose. Objectives that use these special glasses are called apochromats and were first produced by Abbe in the 1870s.

      Conventional objectives do not produce a flat image surface. The field curvature is generally of little importance in the visual use of the microscope because the eye has a reasonable accommodative capability when examining the image. Field curvature is a problem for imaging systems, however. Special objectives with flat-field lenses have been designed for these systems.

High-power objectives
      High-power objectives pose several design problems. Because the focal length of an objective decreases as the N.A. and magnifying power increase, the working distance, or distance from the front of the objective to the top of the slide, is shorter for higher-power objectives. The need to use additional elements in the lens system for high magnifications further shortens the working distance to only 10 to 20 percent of the focal length. Thus, a 40× objective of 4-mm (0.2-inch) focal length may have a working distance of less than 0.4 mm (0.02 inch), so objectives with an increased working distance have been designed. These use a negative lens element between the object and the eyepiece, which has the added attraction of providing some field flattening as well. These objectives are especially of value in use with video systems.

      In objectives with magnifying powers of 25× or greater, meniscus-shaped aplanatic elements are designed into the microscope objective in the space between the object and the pairs of doublets that carry out the relayed imaging. These aplanatic components have the property of converging the light without adding spherical aberration to the image and provide an increase in the N.A. without introducing significant aberration.

      The highest-power microscope objective available is the immersion objective. When this type of objective is used, a drop of oil must be placed between the object on the microscope slide and the objective. The oil used has an R.I. that matches that of the glass in the first component of the objective.

      The first component of immersion objectives is generally a hyper-hemisphere (a small optical surface shaped like a hemisphere but with a boundary curve exceeding 180°), which acts as an aplanatic coupler between the slide and the rest of the microscope objective. An immersion objective with a high N.A. typically consists of a hyper-hemisphere followed by one or two aplanatic collectors and then two or more sets of doublets. Such objectives are made with magnifying powers greater than 50×, the extreme being about 100×.

      Water-immersion lenses are also available. These use water as an immersion liquid and allow biologists to examine specimens in a watery medium without the burden of a cover slip confining the living organisms.

Depth of focus
       Maximum resolving power and depth of focus for a visual microscopeThe large N.A. of a microscope objective restricts the focusing requirements of the objective. The depth of focus is shown in the table (Maximum resolving power and depth of focus for a visual microscope) as the accuracy with which the focal plane must be located in a direction along the axis of the microscope optics in order that the highest possible resolution can be obtained.

The eyepiece
      The eyepiece is selected to examine the relayed image under conditions that are comfortable for the viewer. The magnifying power of the eyepiece generally does not exceed 10×. The field of view is then about 40° total, a convenient value for a relatively simple optical design. The observer places the eye at the exit pupil of the eyepiece, the point at which the light rays leaving the eyepiece come together. In most cases an eye relief (or distance from the exit pupil to the last element of the eyepiece) of about 1 cm is desirable. Too short an eye relief makes viewing difficult for observers who wear corrective eyeglasses.

Image capture
      The objectives described above are usually intended to project an image through an eyepiece for direct viewing by an observer. The use of a photographic recording method permits the capture of a real image in a film holder or digital imaging system without an eyepiece lens. One approach is to remove the eyepiece and place the film holder or digital camera in the focal plane of the eyepiece, thus intercepting the image from the objective directly. A better approach is to use a specifically designed projection eyepiece, which can be adjusted to provide the appropriate magnification coupling the image to the film. Such an eyepiece can incorporate a change in the chromatic aberration correction to accommodate the requirements of the image-capture system.

      Increasingly prevalent today is the use of an electronic detector such as a complementary metal-oxide semiconductor (CMOS) or charge-coupled device (CCD) chip to capture the magnified image as a digital signal. This signal can be transmitted to a computer and translated into an image on the monitor. Software allows the user to take single pictures, moving video sequences, or time-lapse sequences at the click of a mouse. These may be saved for conventional viewing, and image processing can be used to enhance the result. Analysis of area and particle size and distribution is easily done by conventional analytical means once the images have been digitally captured. The production of computer presentations, transmission via e-mail, and ease of printing are benefits that digital imaging brings to the modern microscopist.

The theory of image (optical image) formation
 The objective collects a fan of rays from each object point and images the ray bundle at the front focal plane of the eyepiece. The conventional rules of ray tracing apply to the image formation. In the absence of aberration, geometric rays form a point image of each object point. In the presence of aberrations, each object point is represented by an indistinct point. The eyepiece is designed to image the rays to a focal point at a convenient distance for viewing the image. In this system, the brightness of the image is determined by the sizes of the apertures of the lenses and by the aperture of the pupil of the eye. The focal length and resulting magnification of the objective should be chosen to attain the desired resolution of the object at a size convenient for viewing through the eyepiece. Image formation in the microscope is complicated by diffraction and interference that take place in the imaging system and by the requirement to use a light source that is imaged in the focal plane.

      The modern theory of image formation in the microscope was founded in 1873 by the German physicist Ernst Abbe (Abbe, Ernst). The starting point for the Abbe theory is that objects in the focal plane of the microscope are illuminated by convergent light from a condenser. The convergent light from the source can be considered as a collection of many plane waves propagating in a specified set of directions and superimposed to form the incident illumination. Each of these effective plane waves is diffracted by the details in the object plane: the smaller the detailed structure of the object, the wider the angle of diffraction.

      The structure of the object can be represented as a sum of sinusoidal components. The rapidity of variation in space of the components is defined by the period of each component, or the distance between adjacent peaks in the sinusoidal function. The spatial frequency is the reciprocal of the period. The finer the details, the higher the required spatial frequency of the components that represent the object detail. Each spatial frequency component produces diffraction at a specific angle dependent upon the wavelength of light. As an example, spatial frequency components having a period of 1 μm would have a spatial frequency of 1,000 lines per millimetre. The angle of diffraction for such a component for visible light with a wavelength of 550 nanometres (nm; 1 nanometre is 10−9 metre) will be 33.6°. The microscope objective collects these diffracted waves and directs them to an image plane, where interference between the diffracted waves produces an image of the object.

      Because the aperture of the objective is limited, not all the diffracted waves from the object can be transmitted by the objective. Abbe showed that the greater the number of diffracted waves reaching the objective, the finer the detail that can be reconstructed in the image. He designated the term numerical aperture (N.A.) as the measure of the objective's ability to collect diffracted light and thus also of its power to resolve detail. On this basis it is obvious that the greater the magnification of the objective, the greater the required N.A. of the objective. The largest N.A. theoretically possible in air is 1.0, but optical design constraints limit the N.A. that can be achieved to around 0.95 for dry objectives.

      For the example above of a specimen with a spatial frequency of 1,000 lines per millimetre, the required N.A. to collect the diffracted light would be 0.55. Thus, an objective of 0.55 N.A. or greater must be used to observe and collect useful data from an object with details spaced 1 μm apart. If the objective has a lower N.A., the details of the object will not be resolved. Attempts to enlarge the image detail by use of a high-power eyepiece will yield no increase in resolution. This latter condition is called empty magnification.

      The wavelength of light is shortened when it propagates through a dense medium. In order to resolve the smallest possible details, immersion objectives are able to collect light diffracted by finer details than can objectives in air. The N.A. is multiplied by the index of refraction of the medium, and working N.A.'s of 1.4 are possible. In the best optical microscopes, spatial frequency components with periods as small as 0.4 μm can be observed. Note that Leeuwenhoek's lenses could reveal microfibres down to 0.7 m in thickness.

Specialized optical microscopes
      The basic form of the optical microscope is modified by designers for expediency, and a range of special adaptations is available for specific purposes. Some have been designed for ergonomics and others for ease of access to components, while some have been aimed at a specific age group and others at a clearly defined purpose. The largest optical microscope put into production, the Burch reflector, weighed 200 kg (440 pounds), while the smallest functioning optical microscope—a single-lens instrument made by British optician Horace Dall—weighs no more than 24 grams (0.8 ounce). Leeuwenhoek's microscopes typically weighed less than 15 grams (0.5 ounce). The most successful small microscope was designed by British doctor John McArthur, and McArthur microscopes have been produced by several manufacturers. Some specialized microscopes intended for handheld use (e.g., the Microwatcher) incorporate the illuminator and lens systems into a single unit. More recently, small digital microscopes have been introduced.

Inverted microscopes
      For some special purposes, notably the examination of cell cultures, it is more practical if the microscope is mounted upside down. In this form of microscope, the inverted microscope, the light source and condenser are situated uppermost and direct light down through the stage. The objective is set with its front element uppermost, and the eyepieces are angled upward so that the observer can study specimens that are still in their watery medium. Inverted microscopes are important in biology and medical research.

Stereoscopic microscopes
      Binocular stereomicroscopes are a matched pair of microscopes mounted side by side with a small angle between the optical axes. The object is imaged independently to each eye, and the stereoscopic effect, which permits discrimination of relief on the object, is retained. The effect can be exaggerated by proper choice of the design parameters for the microscopes. For practical reasons, the magnifying power of such instruments is usually in the range of 5–250×. Such microscopes are important in any work in which fine adjustment of tools or devices is to be made. For example, the stereomicroscope is often used in biological laboratories for dissection of subjects and in the operating room for microsurgical procedures. Moderate-power stereomicroscopes are even more widely used in the electronics manufacturing industry, where they enable technicians to monitor the bonding of leads to integrated circuits (integrated circuit).

Polarizing microscopes
      Polarizing microscopes are conventional microscopes with additional features that permit observation under polarized light (light). The light source of such an instrument is equipped with a polarizing filter, the polarizer, so that the light it supplies is linearly polarized (i.e., the light waves vibrate in a given direction rather than randomly in all directions as in ordinary light). When this linearly polarized light passes through the object under examination, it may be unaffected or, if the object is birefringent, it may be split into two beams with different polarizations. A second filter, a polarization analyzer, is fitted to the eyepiece, where it blocks out all but one polarization of the light. The analyzer can be rotated to obtain maximum contrast in the image, and so the direction of polarization of the light transmitted through the object can be determined. The eyepiece can also be equipped with a polarization retarder, which shifts the phase of the light between selected polarization directions and which can be rotated to measure the amount of elliptic polarization produced by the specimen.

      Many precautions must be taken in the design and construction of a polarizing microscope to avoid using optical components that introduce undesirable polarization retardation in the beam of light after it has left the object. There is a basic limitation placed upon the use of objectives with high N.A.'s wherein the necessary high angles of incidence on the surface produce some depolarization. Specialized microscope objectives that minimize this effect have been designed and produced. Polarizing microscopes are primarily used to examine the nature of crystals in geologic samples and to analyze the details of birefringence and stress in biological structures. They have been of crucial importance in the detection and monitoring of asbestos fibres.

Metallographic microscopes
      Metallographic microscopes are used to identify defects in metal surfaces, to determine the crystal grain boundaries in metal alloys, and to study rocks and minerals. This type of microscope employs vertical illumination, in which the light source is inserted into the microscope tube below the eyepiece by means of a beam splitter. Light shines down through the objective and is focused through the objective onto the specimen. The light reflected or scattered back to the objective is then imaged back at the eyepiece. In this manner, opaque objects such as metals can be examined under the microscope. Such systems also have applications in forensic science and diagnostic microscopy.

Reflecting microscopes
      Microscopes of this type feature reflecting rather than refracting objectives. They are used to carry out microscopy over a wide range of visible light and especially in the ultraviolet or infrared regions, where conventional optical glasses do not transmit. The reflecting microscope objective usually consists of two components: a relatively large, concave primary mirror and a smaller, convex secondary mirror, which is located between the primary mirror and the object and serves to relay the image from the primary mirror to the focal plane of the eyepiece. Although reflecting objectives do not have chromatic aberration, they need to be corrected for spherical aberrations, either by using aspheric reflecting components or by adding appropriate refracting lenses.

Phase-contrast microscopes
      Many biological objects of interest consist of cell structures such as nuclei that are almost transparent; they transmit as much light as the mounting medium that surrounds them does. Because there is no colour or transmission contrast in such an object, it is not possible to observe the structure using a conventional optical microscope.

      However, the R.I. of the cell structure varies slightly from the surrounding material, and it is possible to exploit this difference. The propagation of light through such an object provides a change in the optical path across the object, as well as a resulting shift in the phase of the light that has passed through the structure of interest relative to light passing around the structure. This phase-shift information can be used to form a visible image if it is converted into intensity variations that are detectable by the observer. The Dutch physicist Frits Zernike (Zernike, Frits) developed a method for doing just that in 1934. (He won the Nobel Prize for Physics in 1953 for his invention.) In a phase-contrast microscope the phase difference between light that is diffracted by a specimen and light that is direct and undeflected is one-quarter of a wavelength or less. By placing an appropriate mask in the back focal plane of the objective to provide selective filtering of the diffracted light, Zernike increased this phase difference by another quarter wavelength. Waves that differ in phase by half a wavelength cancel one another. In places in the phase image where this occurs, no light is transmitted. As a result, phase differences caused by variations in the specimen appear as intensity variations in the image.

      There are several approaches to achieving a good-quality image by this technique. One of the most common is the use of an annular light source imaged onto an annular mask in the back focal plane. Other techniques use edges, small dots, or other combinations of source shape and mask shape.

Interference microscopes
      Although all optical microscopes in the strict sense create images by diffraction, interference microscopy creates images using the difference between an interfering beam unmodified by the specimen and an otherwise identical beam that illuminates it. A beam splitter divides light into two paths, one of which passes through the specimen while the other bypasses it. When the two beams are combined, the resulting interference between them reveals the structure of the specimen. The first successful system, invented by British microscopist Francis Smith and French physicist Maurice Françon in 1947, used quartz lenses to produce reference and image-forming beams that were perpendicularly polarized. Although this worked well for continuous specimens, in the case of particulates it was better to have the reference beam pass through a bare area of the specimen preparation, and by 1950 the use of half-silvered surfaces and slightly tapering slides allowed polarized light to be dispensed with.

      Meanwhile, differential interference contrast (DIC) was developed by Polish-born French physicist Georges Nomarski in 1952. A beam-splitting Wollaston prism emits two beams of polarized light that are plane-polarized at right angles to each other and that slightly diverge. The rays are focused in the back plane of the objective, where they pass through a composite prism that is isotropic at the midpoint, with an increasing optical path difference away from the midpoint. The background colour of the image depends on the setting of the prism, which can be slid longitudinally to produce a spectrum of colours that vary through to black. The sensitivity is greatest in the middle position, but the colour contrast is greatest when a strong background tint is selected. More-recent developments include asymmetrical illumination contrast and modulation contrast, which exploit offset or oblique illumination.

Confocal microscopes
      The field of view of a microscope is limited by the geometric optics and by the ability to design optics that provide a constant aberration correction over a large field of view. If a scanning arrangement is used, the objective can be used over a continuous series of small fields and the results used to build up an image of a larger region.

      The concept has been harnessed in the confocal scanning microscope. Confocal microscopy's main feature is that only what is in focus is detected, and anything out of focus appears as black. This is achieved by focusing the light source, usually a laser, to a point and detecting the image through a pinhole. Since only light from the focused point contributes to the final image in a confocal system, it is particularly useful for the eludication of fine and three-dimensional structures of biological specimens.

      In a laser scanning confocal microscope (LSCM), the focal point of a laser is scanned across a specimen to build up a two-dimensional optical section. Three-dimensional images can be reconstructed by taking a series of two-dimensional images at different focal depths in the specimen (known as a Z-series). Argon and krypton/argon lasers are commonly used, and a multiphoton system has been designed in which an argon laser excites a synthetic titanium-sapphire. A range of colours can thus be utilized.

      Specimens are distinguished by fluorescence. Some components fluoresce spontaneously, but most are stained with dyes that fluoresce under the rays from a laser. Scanning rates can be high—in some systems a line of image is scanned every 0.488 millisecond (one millisecond is one thousandth of a second)—so a sequence of images showing how a specimen changes over time can be easily assembled. Methods like these are used to study the behaviour of living cells.

Ultraviolet microscopes
      Ultraviolet (UV) microscopy was developed in the early 20th century by the German scientists August Köhler and Moritz von Rohr. Because of the shorter wavelength of UV light, higher resolution was possible, but the opacity of conventional glass lenses to these wavelengths necessitated the use of either a reflecting microscope or specially made quartz lenses. UV microscopes became most widely used for fluorescent microscopy, in which the UV caused microscope stains to fluoresce. In modern microscopy, lamps in the range from deep blue to near UV are more often used for this purpose. However, the interest in UV led to the recognition that the electron beam could be used as an illuminant of very short wavelength, and it was this that gave rise to interest in the electron microscope (microscope).

Robert R. Shannon Brian J. Ford

Electron microscopes (electron microscope)

 Fundamental research by many physicists in the first quarter of the 20th century suggested that cathode rays (cathode ray) (i.e., electrons (electron)) might be used in some way to increase microscope resolution. French physicist Louis de Broglie (Broglie, Louis-Victor, 7e duc de) in 1924 opened the way with the suggestion that electron beams might be regarded as a form of wave motion. De Broglie derived the formula for their wavelength, which showed that, for example, for electrons accelerated by 60,000 volts (or 60 kilovolts [k]), the effective wavelength would be 0.05 angstrom (Å)—i.e., 1/100,000 that of green light. If such waves could be used in a microscope, then a considerable increase in resolution would result. In 1926 it was demonstrated that magnetic or electrostatic fields could serve as lenses (lens) for electrons or other charged particles. This discovery initiated the study of electron optics, and by 1931 a two-lens electron microscope had been devised, which produced images of the electron source. In 1933 a primitive electron microscope was built, and in 1935 German electrical engineer Max Knoll produced a scanned image of a solid surface. The resolution of the optical microscope was soon surpassed.

      German physicist Manfred, baron von Ardenne, and British electronic engineer Charles Oatley laid the foundations of transmission (in which the electron beam travels through the specimen) and scanning electron microscopy (in which the electron beam ejects from the sample other electrons that are then analyzed), which are most notably recorded in baron von Ardenne's book Elektronen-Übermikroskopie (1940). Further progress in the construction of electron microscopes was delayed during World War II but received an impetus in 1946 with the invention of the stigmator, which compensates for astigmatism of the objective lens, after which production became more widespread.

      The transmission electron microscope (TEM) can image specimens up to 1 μm in thickness. The scanning electron microscope (SEM), in which a beam of electrons is scanned over the surface of a solid object, is used to build up an image of the details of the surface structure. The environmental scanning electron microscope (ESEM) can generate a scanned image of a specimen in an atmosphere, unlike the SEM, and is amenable to the study of moist specimens, including some living organisms.

      Combinations of techniques have given rise to the scanning transmission electron microscope (STEM), which combines the methods of TEM and SEM, and the electron-probe microanalyzer, or microprobe analyzer, which allows a chemical analysis of the composition of materials to be made using the incident electron beam to excite the emission of characteristic X-rays (X-ray) by the chemical elements in the specimen. These X-rays are detected and analyzed by spectrometers built into the instrument. Microprobe analyzers are able to produce an electron scanning image so that structure and composition may be easily correlated.

Operating principles
      Although there are similarities in principle between the layout of optical and electron microscopes, in practice the two are very different. The conventional electron microscope requires that the electron beam be in a vacuum, because electrons cannot ordinarily travel an appreciable distance in air at atmospheric pressure. The column of the electron microscope is evacuated by pumps, and the specimens and any other necessary apparatus are introduced into the vacuum by means of air locks. Unlike the optical microscope, in which the lenses (lens) are of fixed focus and the distance between specimen and objective lens is varied, the electron microscope has variable-focus lenses, and the distance between specimen and objective lens and the separation of the lenses remain constant. The magnification is determined mainly by the value of the current (for magnetic lenses) through the intermediate and projector lens coils. The image is focused by changing the current through the objective lens coil. Another difference is that the optical microscope is usually operated so that the image is a virtual one, while in the electron microscope the final image is invariably real and is visualized on a fluorescent screen or recorded for study on a photographic plate or—more usually in today's laboratory—on a digital imaging system.

      In the optical microscope the image is formed by absorption of light in the specimen; in the electron microscope the image results from a scattering of electrons by atoms in the specimen. A heavy atom is more effective in scattering than one of low atomic number, and the presence of heavy atoms will increase the image contrast. The electron microscopist may incorporate more heavy atoms into the specimen for this purpose.

      Early microscopes relied on electrostatic lenses, but modern instruments use electromagnetic lenses. These consist of a solenoid of wire together with a magnetic pole piece that creates and concentrates a magnetic field. The lenses used for the condenser and projector system of the microscope differ from the objective lens only in details. For example, the manufacturing and performance tolerances for a condenser or projector lens are less demanding than for an objective lens.

      Efforts to improve the resolution of the electron microscope have tended toward production of a single-field condenser-objective lens of low aberrations (aberration). In such a lens, the upper part acts as a condenser and the lower as the objective; the specimen is inserted into the centre of the lens, where the axial magnetic field (the field along the axis of the instrument) is at a maximum.

      All electron-optical lenses show spherical aberration, distortion, coma, astigmatism, curvature of field, and chromatic aberration due to variations in the wavelengths within the electron beam. Such changes of electron velocity may be either due to variations in the high-voltage supply to the electron gun or due to energy losses from collisions of electrons with atoms in the specimen. The first effect may be minimized by careful stabilization of the high-voltage supply; and for the very thin specimens and the high electron energies commonly used, the second effect may usually be neglected. The resolving power of the microscope is ultimately limited by the spherical aberration of the objective lens. It is not possible to correct this aberration by adding a second lens of opposite characteristics, as can be done for the optical microscope, because magnetic electron lenses are always convergent. Computer-aided lens design has led to great improvements in performance, but electron lenses still require much smaller N.A.'s than do optical lenses in order to function optimally.

      Astigmatism in the electron microscope is largely due to deviations from cylindrical symmetry in the radial components of the magnetic field of the lens and is the result of imperfect construction of the lens. The interaction of the electron beam with residual gas molecules in the column may also lead to deposits along the beam path that charge up under the influence of the beam and introduce asymmetries. Astigmatism may usually be completely corrected by use of the stigmators fitted to the objective lens.

The transmission electron microscope
 The transmission electron microscope (TEM) has three essential systems: (1) an electron gun, which produces the electron beam, and the condenser system, which focuses the beam onto the object, (2) the image-producing system, consisting of the objective lens, movable specimen stage, and intermediate and projector lenses, which focus the electrons passing through the specimen to form a real, highly magnified image, and (3) the image-recording system, which converts the electron image into some form perceptible to the human eye. It usually consists of a fluorescent screen for viewing and focusing the image and a digital camera for permanent records. In addition, a vacuum system, consisting of pumps and their associated gauges and valves, and power supplies are required.

The electron gun and condenser system
      The source of electrons, the cathode, is a heated V-shaped tungsten filament or, in high-performance instruments, a sharply pointed rod of a material such as lanthanum hexaboride. The filament is surrounded by a control grid, sometimes called a Wehnelt cylinder, with a central aperture arranged on the axis of the column; the apex of the cathode is arranged to lie at or just above or below this aperture. The cathode and control grid are at a negative potential equal to the desired accelerating voltage and are insulated from the rest of the instrument. The final electrode of the electron gun is the anode, which takes the form of a disk with an axial hole. Electrons leave the cathode and shield, accelerate toward the anode, and, if the stabilization of the high voltage is adequate, pass through the central aperture at a constant energy. The control and alignment of the electron gun are critical in ensuring satisfactory operation.

      The intensity and angular aperture of the beam are controlled by the condenser lens system between the gun and the specimen. A single lens may be used to converge the beam onto the object, but, more commonly, a double condenser is employed. In this the first lens is strong and produces a reduced image of the source, which is then imaged by the second lens onto the object. Such an arrangement is economical of space between the electron gun and the object stage and is more flexible, because the reduction in size of the image of the source (and hence the final size of illuminated area on the specimen) may be varied widely by controlling the first lens. The use of a small spot size minimizes disturbances in the specimen due to heating and irradiation.

The image-producing system
      The specimen grid is carried in a small holder in a movable specimen stage. The objective lens is usually of short focal length (1–5 mm [0.04–0.2 inch]) and produces a real intermediate image (optical image) that is further magnified by the projector lens or lenses. A single projector lens may provide a range of magnification of 5:1, and by the use of interchangeable pole pieces in the projector a wider range of magnifications may be obtained. Modern instruments employ two projector lenses (one called the intermediate lens) to permit a greater range of magnification and to provide a greater overall magnification without a commensurate increase in the physical length of the column of the microscope.

      For practical reasons of image stability and brightness, the microscope is often operated to give a final magnification of 1,000–250,000× on the screen. If a higher final magnification is required, it may be obtained by photographic or digital enlargement. The quality of the final image in the electron microscope depends largely upon the accuracy of the various mechanical and electrical adjustments with which the various lenses are aligned to one another and to the illuminating system. The lenses require power supplies of a high degree of stability; for the highest standard of resolution, electronic stabilization to better than one part in a million is necessary. The control of a modern electron microscope is carried out by a computer, and dedicated software is readily available.

Image recording
      The electron image is monochromatic and must be made visible to the eye either by allowing the electrons to fall on a fluorescent screen fitted at the base of the microscope column or by capturing the image digitally for display on a computer monitor. Computerized images are stored in a format such as TIFF or JPEG and can be analyzed or image-processed prior to publication. The identification of specific areas of an image, or pixels with specified characteristics, allows spurious colours to be added to a monochrome image. This can be an aid to visual interpretation and teaching and can create a visually attractive picture from the raw image.

The scanning electron microscope
 The scanning electron microscope (SEM), designed for directly studying the surfaces of solid objects, utilizes a beam of focused electrons of relatively low energy as an electron probe that is scanned in a regular manner over the specimen. The electron source and electromagnetic lenses that generate and focus the beam are similar to those described for the TEM. The action of the electron beam stimulates emission of high-energy backscattered electrons and low-energy secondary electrons from the surface of the specimen.

      No elaborate specimen-preparation techniques are required for examination in the SEM, and large and bulky specimens may be accommodated. It is desirable that the specimen be rendered electrically conducting; otherwise a sharp picture will not be obtained. Conductivity is usually achieved by evaporating a film of metal, such as gold, 50–100 Å thick onto the specimen in a vacuum (such a thickness does not materially affect the resolution of the surface details). If, however, the scanning electron microscope can be operated at 1–3 kV of energy, then even nonconducting specimens may be examined without the need for a metallic coating.

      Scanning instruments have been combined with TEMs to create scanning transmission electron microscopes. These have the advantages that very thick sections may be studied without chromatic aberration limitation and electronic methods may be used to enhance the contrast and brightness of the image.

The environmental scanning electron microscope
      The benefits of the environmental scanning electron microscope (ESEM) include obviating the need for special specimen preparation (gold sputtering, for example, is unnecessary) and examining a specimen at various temperatures and in a gaseous atmosphere, thus obviating the need for a hard vacuum. The environment in an ESEM can be selected from among water vapour, air, nitrogen, argon, and oxygen, and such dynamic phenomena as wetting, drying, melting, freezing, crystallization, and corrosion can be observed with an ESEM.

      The key to the functioning of an ESEM is the design of the secondary electron detector, which relies on gas ionization. Primary electrons are emitted from the gun, and they eject secondary electrons from the surface of the specimen. These secondary electrons are accelerated toward the moderate electric field of the detector. Collisions between the electrons and gas molecules liberate further free electrons that perpetuate the signal. Positive ions in the gaseous environment neutralize an excess electron charge on the specimen, and controlling the pressure reduces surface charging on the specimen.

      A mechanical substage is capable of allowing tensile, compression, flexion, and load control modes, with the possibility of using micromanipulators and a pipette, which can add liquids during observation. A wide range of stage temperatures is available. It is thus possible to study corrosion as it happens and even to make routine observations of living arthropods (arthropod).

High-voltage instruments
      Several different types of instruments have been constructed to operate at accelerating voltages in excess of the 200–300 kV normally used in the conventional transmission instrument. High-voltage microscopes now in commercial production are designed for accelerating voltages of up to 1,500 kV.

      These instruments have several advantages over the conventional TEM: (1) the theoretical resolving power of the instrument increases as the accelerating voltage increases; (2) thick specimens are easily penetrated by the beam; (3) chromatic aberration caused by energy losses and scattering in the specimen is decreased; and (4) specimen heating and irradiation damage of organic samples are decreased. Many metals and semiconductors suffer increased damage at these high energies, however, because the incident electrons may knock an atom from its correct position in the crystal lattice.

      Although the gain in resolution at 1,000 kV is theoretically about two and a half times that of a 100-kV instrument, such increases have not been fully achieved in practice. It is primarily for the increased penetrating power and consequent reduction in chromatic aberration that the high-voltage instruments are used, as in the study of metals and alloys, for example. Some biological systems, such as bacteria and whole cells contained within a quartz chamber, may also be examined at high voltage. However, specimen damage due to the energetic electron beam is considerable.

The electron-probe microanalyzer
      A limitation of the conventional electron microscope is that it provides no chemical information. Electron-probe microanalyzers have been developed since 1947 to carry out nondestructive elemental analysis at resolutions approaching those of the transmission electron microscope. This is done by measuring the energy and intensity of the characteristic X-rays emitted by a specimen when a focused electron beam impinges on it. As in the scanning electron microscope, the probe is scanned so that an image of the distribution of a chosen element may be built up on a cathode-ray tube.

      X-ray microprobe analysis has proven to be so valuable that a majority of SEMs, as well as many TEMs, are now equipped with X-ray spectrometers as accessories. The technique has found wide applications in mineralogy, metallurgy, and solid-state science, as well as in the clinical and life sciences.

The field-emission microscope
      In this instrument a wire with a sharpened tip is mounted in a cathode-ray tube. Electrons are drawn from the tip by a high electrical field and travel toward the screen on which the image is formed. Only strong metals, such as tungsten, platinum, and molybdenum, can be examined in this way, because the high field at the tip exerts a large mechanical stress. The magnification is proportional to the ratio of the radius of curvature of the screen on which the image forms to the radius of the metal tip; it may reach up to 1,000,000×.

      A development of the field-emission microscope is the field-ion microscope, in which the tip is surrounded by a low pressure of helium gas. The gas is ionized at the atom planes on the tip and produces an image that can have a magnification of up to 10,000,000×. The field-ion microscope has been applied mainly to the study of metals and semiconductors, but a few biological images have been obtained. A further development of the field-ion microscope is the atom probe. In this instrument, individual atoms are removed from the tip by pulsing the electric field. The atoms pass through a time-of-flight spectrometer, which measures their energy and charge-to-mass ratio. In this way the chemical nature of each atom in the field-ion image may be determined.

Savile Bradbury David C. Joy Brian J. Ford

Acoustic microscopes
      In the early 1940s Soviet physicist Sergei Y. Sokolov proposed the use of ultrasound in a microscope and showed that sound waves with a frequency of 3,000 megahertz (MHz) would have a resolution equal to that of the optical microscope. However, at that time the required technology did not exist. Since then the technology has been developed, and the high frequencies required for Sokolov's microscope are found in the microwave systems used for radar and for satellite communications. During the 1970s several groups of researchers in the United States employed these frequencies to build sound systems. The microscope that evolved from this effort is known as the scanning acoustic microscope.

      Transducers (transducer) produce frequencies of » 5–150 MHz that are modulated and diffracted by structures within a sample. Computer analysis of the resulting waveform gives an image of what lies within. The sound reflectance is related to the acoustic differences of two components (Pr):

Pr = (Z2 - Z1)/(Z2 + Z1),
where Z1 and Z2 are the acoustic impedances of the first and second material, respectively. Solid-state systems allow the beam to be scanned across the specimen, enabling the nondestructive inspection of products such as integrated circuit (IC) packages. For these applications, 25–50-MHz transducers are employed to give real-time images that are amenable to automated computer analysis. Plastic and ceramic ICs, along with capacitors, resistors (resistor), and semiconductors (semiconductor), have been tested using acoustic microscopy techniques.

      Biological applications are also beginning to emerge. For example, it is believed that early sclerotic changes in the bones of racehorses might be detected by acoustic microscopy, and the technique may be applied to sports medicine.

      Further research is currently under way into tomographic acoustic micro-imaging (TAMI), scanning electron acoustic microscopy (SEAM), and scanning probe acoustic microscopy (SPAM), which have been developed from conventional electron microscopy.

Brian J. Ford

Scanning tunneling microscopes
      The scanning tunneling microscope (STM) appeared in 1981 when Swiss physicists Gerd Binnig (Binnig, Gerd) and Heinrich Rohrer (Rohrer, Heinrich) set out to build a tool for studying the local conductivity of surfaces. Its principle of operation is based on the quantum mechanical phenomenon known as tunneling, in which the wavelike properties of electrons (electron) permit them to “tunnel” beyond the surface of a solid into regions of space that are forbidden to them under the rules of classical physics. The probability of finding such tunneling electrons decreases exponentially as the distance from the surface increases. The STM makes use of this extreme sensitivity to distance. The sharp tip of a tungsten needle is positioned a few angstroms from the sample surface. A small voltage is applied between the probe tip and the surface, causing electrons to tunnel across the gap. As the probe is scanned over the surface, it registers variations in the tunneling current, and this information can be processed to provide a topographical image of the surface.

      Binnig and Rohrer chose the surface of gold for their first image. When the image was displayed on the screen of a television monitor, they saw rows of precisely spaced atoms and observed broad terraces separated by steps one atom in height. Binnig and Rohrer had discovered in the STM a simple method for creating a direct image of the atomic structure of surfaces. Their discovery opened a new era for surface science, and their impressive achievement was recognized with the award of the Nobel Prize for Physics in 1986.

      The STM is an electron microscope (microscope) with a resolution sufficient to resolve single atoms. The sharp tip in the STM is similar to that in the SEM, but the differences in the two instruments are profound. In the SEM, electrons are extracted from the tip with a series of positively charged plates placed a few centimetres downstream from the tip. The electrons at the apex of the tip are confined to the region within the metal by a potential barrier. The attractive force from the positive charge on the plates is sufficient to permit the electrons to overcome the barrier and enter the vacuum as free particles. The apertures in the downstream plates form an electron lens that converts the diverging beam from the tip into a beam converging to a focus on the surface of the sample.

      In the STM, the plates that form the lens in the SEM are removed, and the tip is positioned close to the sample. The electrons move through the barrier in a way that is similar to the motion of electrons in a metal. In metals, electrons appear to be freely moving particles, but this is illusory. In reality, the electrons move from atom to atom by tunneling through the potential barrier between two atomic sites. In a typical case, with the atoms spaced 5 Å apart, there is a finite probability that the electron will penetrate the barrier and move to the adjacent atom. The electrons are in motion around the nucleus, and they approach the barrier with a frequency of 1017 per second. For each approach to the barrier, the probability of tunneling is 10−4, and the electrons cross the barrier at the rate of 1013 per second. This high rate of transfer means that the motion is essentially continuous and tunneling can be ignored in metals.

      Tunneling cannot be ignored in the STM; indeed, it is all-important. When the tip is moved close to the sample, the spacing between the tip and the surface is reduced to a value comparable to the spacing between neighbouring atoms in the lattice. In this circumstance, the tunneling electron can move either to the adjacent atoms in the lattice or to the atom on the tip of the probe. The tunneling current to the tip measures the density of electrons at the surface of the sample, and this information is displayed in the image. In semiconductors (semiconductor), such as silicon, the electron density reaches a maximum near the atomic sites. The density maxima appear as bright spots in the image, and these define the spatial distribution of atoms. In metals, on the other hand, the electronic charge is uniformly distributed over the entire surface. The tunneling current image should show a uniform background, but this is not the case. The interaction between tip and sample perturbs the electron density to the extent that the tunneling current is slightly increased when the tip is positioned directly above a surface atom. The periodic array of atoms is clearly visible in the images of materials such as gold, platinum, silver, nickel, and copper.

      Several surfaces have been studied with the STM. The arrangement of individual atoms on the metal surfaces of gold, platinum, nickel, and copper have all been accurately documented. The absorption and diffusion of different species such as oxygen and the epitaxial (epitaxy) growth of gold on gold, silver on gold, and nickel on gold also have been examined in detail.

      The surfaces of silicon have been studied more extensively than those of any other material. The surfaces are prepared by being heated in vacuum to temperatures so high that the atoms there rearrange their positions in a process called surface reconstruction. The reconstruction of the silicon surface designated (111) has been studied in minute detail. Such a surface reconstructs into an intricate and complex pattern known as the Takayanagi 7 × 7 structure. The position, the chemical reactivity, and the electronic configuration of each atomic site on the 7 × 7 surface has been measured with the STM. The reconstruction of the silicon surface designated (100) is more simple. The surface atoms form pairs, or dimers, that fit into rows that extend across the entire silicon surface.

      “Vacuum tunneling” of electrons from tip to sample can take place even though the environment in the region surrounding the tip is not a vacuum but is filled with molecules of gas or liquids. With a tip-sample spacing as small as 5 Å, there is little room for molecules—even though they may exist in the surrounding atmosphere. The STM can operate in ambient atmosphere as well as in high vacuum. Indeed, it has been operated in air, in water, in insulating fluids, and in the ionic solutions used in electrochemistry. It is much more convenient than ultrahigh-vacuum instruments. When a high-vacuum environment is employed, its purpose is not to improve the performance of the STM but rather to ensure the cleanliness of the sample surface.

      The STM can be cooled to temperatures less than 4 K (−269 °C, or −452 °F)—the temperature of liquid helium. It can be heated above 973 K (700 °C, or 1,300 °F). The low temperature is used to investigate the properties of superconducting materials, while the high temperature is employed to study the rapid diffusion of atoms across the surface of metals and their corrosion.

      The STM is used primarily for imaging, but there are many other modalities that have been explored. The strong electric field between tip and sample has been utilized to move atoms along the sample surface. It has been used to enhance the etching rates in various gases. In one instance a voltage of four volts was applied; the field at the tip was strong enough to remove atoms from the tip and deposit them on the substrate. This procedure has been employed with a gold tip to fabricate small gold islands or clusters on the substrate with several hundred atoms of gold in each cluster. These nanostructures are used to pattern the surface on a scale that is unprecedented.

Calvin F. Quate

X-ray microscopes
      Little use has been found for the X-ray microscope. The basic device uses the emission of X-rays from a point source to cast an enlarged image on a phosphor screen, and a successful X-ray microscope was made in 1951 by British physicists Ellis Coslett and William Nixon. It was the first such instrument whose resolution was comparable to that of an optical microscope and was hailed as a means of examining hidden structures in rocks, metals (metal), bone, teeth, ores, and wood. After decades in abeyance, interest is once more being shown in the capacities of the X-ray microscope. There is particular interest in soft X-rays with an energy of 100–1,000 electron volts (electron volt) (eV), equivalent to a wavelength down to 1 nm (as opposed to about 500 nm for green light). Biological specimens, polymers, soil, and geological samples have been studied using modern X-ray techniques. The fact that X-ray microscopy can lead to higher resolution than can the best optical microscope is adding impetus to this field of research.

Brian J. Ford

Additional Reading
Informative works on the history of the microscope include Robert Hooke, Micrographia (1665, reissued 1961); B.J. Ford, Single Lens, Story of the Simple Microscope (1985); Clifford Dobell, Antony van Leeuwenhoek and His “Little Animals” (1932, reissued 1960); Savile Bradbury, The Evolution of the Microscope (1967); and Ernst Ruska, “The Development of the Electron Microscope and of Electron Microscopy,” Reviews of Modern Physics 59(3/1):627–638 (July 1987), the birth and growth of electron microscopy recounted by its founding father.General surveys of the subject, with details on features and applications, are found in H.N. Southworth, Introduction to Modern Microscopy (1975); L.C. Martin, The Theory of the Microscope (1966); T.G. Rochow and E.G. Rochow, An Introduction to Microscopy by Means of Light, Electrons, X-Rays, or Ultrasound (1978); E.A. Ash, Scanned Image Microscopy (1980); W.G. Hartley, The Light Microscope (1993); Jeremy Burgess, Michael Marten, and Rosemary Taylor, Microcosmos (1987); and R.J. Oldfield, Light Microscopy: An Illustrated Guide (1994).A wide-ranging and well-illustrated introduction to electron microscopy, suitable for beginners as well as for more-advanced users, is offered in I.M. Watt, The Principles and Practice of Electron Microscopy (1985). J.I. Goldstein et al., Scanning Electron Microscopy and X-Ray Microanalysis (1981), a technical book that is not unduly mathematical, studies in detail all facets of the scanning electron microscope and electron-probe microanalyzer. P.B. Hirsch et al., Electron Microscopy of Thin Crystals (1965, reissued 1977), is a classic treatise on transmission electron microscopy. Shinya Inoue and K.R. Spring, Video Microscopy: The Fundamentals (1997), is a key work in its field.Andrew Briggs, An Introduction to Scanning Acoustic Microscopy (1985), is a concise illustrated handbook. An informative introduction to scanning tunneling microscopes without the heavy technical details is provided in the following review articles: Gerd Binnig and Heinrich Rohrer, “The Scanning Tunneling Microscope,” Scientific American 253(2):50–56 (August 1985); J.A. Golovchenko, “The Tunneling Microscope: A New Look at the Atomic World,” Science 232:48–53 (April 4, 1986); and C.F. Quate, “Vacuum Tunneling: A New Technique for Microscopy,” Physics Today 39(8):26–33 (August 1986). R.J. Behm, Nicolás Garcia, and Heinrich Rohrer (eds.), Scanning Tunneling Microscopy and Related Methods (1990), is an advanced series of lectures relating to the new microscopy.Robert R. Shannon David C. Joy Calvin F. Quate Brian J. Ford

* * *

Universalium. 2010.

Игры ⚽ Поможем написать курсовую

Look at other dictionaries:

  • microscope — [ mikrɔskɔp ] n. m. • 1656; lat. mod. microscopium (1618), du gr. ♦ Instrument d optique qui permet de voir des objets invisibles à l œil nu grâce à un système de lentilles. Microscope qui grossit mille fois. Étude, examen des objets visibles au… …   Encyclopédie Universelle

  • Microscope — Cette page d’homonymie répertorie les différents sujets et articles partageant un même nom …   Wikipédia en Français

  • MicroScope — magazine Editor Simon Quicke Categories Computer magazine Frequency Monthly Circulation 22,275 First issue September 1982 Company TechTarget …   Wikipedia

  • Microscope — Mi cro*scope, n. [Micro + scope.] An optical instrument, consisting of a lens, or combination of lenses, for making an enlarged image of an object which is too minute to be viewed by the {naked eye}. [1913 Webster] {Compound microscope}, an… …   The Collaborative International Dictionary of English

  • Microscope — ist der Name eines Kleinsatelliten, den Frankreich 2012 in eine sonnensynchrone Umlaufbahn in 710 km Höhe bringen will. Er soll das Äquivalenzprinzip mit einer Genauigkeit, die besser ist als 10 15, überprüfen. Dazu trägt er zwei Körper aus… …   Deutsch Wikipedia

  • microscope — [mī′krə skōp΄] n. [ModL microscopium: see MICRO & SCOPE] an instrument consisting essentially of a lens or combination of lenses, for making very small objects, as microorganisms, look larger so that they can be seen and studied: see also… …   English World dictionary

  • microscope — (n.) 1650s, from Mod.L. microscopium, lit. an instrument for viewing what is small, from Gk. micro (see MICRO (Cf. micro )) + skopion, from skopein to look, see (see SCOPE (Cf. scope)) …   Etymology dictionary

  • microscope — MICROSCOPE. s. m. Terme pris du Grec. On appelle ainsi un instrument qui grossit tellement les objets par la disposition du verre au travers duquel on les regarde, qu on en distingue aisément jusqu aux moindres petites parties …   Dictionnaire de l'Académie française

  • microscope — ► NOUN ▪ an optical instrument for magnifying very small objects. ORIGIN from Greek mikros small + skopein look at …   English terms dictionary

  • Microscope — This article is about microscopes in general. For light microscopes, see optical microscope. Microscope Us …   Wikipedia

Share the article and excerpts

Direct link
Do a right-click on the link above
and select “Copy Link”